Category: Pleated Front Shirt

The Collar

Installing the collar can be a little intimidating at first, but it’s really just a long series of small steps and will become second nature soon enough.

Begin by marking the seam allowance (1/2″) at both ends along the bottom edge of the collar, on the wrong side. This will help us attach the collar with the proper alignment.

Just as a note, when marking the collar, try to be as light as you can in your markings, using a white chalk or very light pencil. I used a pencil, making the marks dark enough to show up on camera, but there was a great risk of the lead bleeding through to the right side, especially when pressing.

With right sides together, pin the bottom edge of the collar to the neck seam at the center back.

Moving to one end of the collar, pin the end of the collar to the neck at the placket, ensuring that the mark you just made is just past the edge of the placket. Repeat for the other end as well.

Now baste the collar to the neck, from the center back to the front, distributing any fullness with your fingers as you work. If you prefer you could pin the rest of the collar before basting.

Repeat for the other half of the collar. If you look carefully at my attempt, on the left side nearer to the front, you can see a small pleat starting to form. I wish I had noticed this earlier, but alas. It should have been more evenly distributed.

Sew the collar seam from end to end, with the collar facing down, using a 1/2″ seam allowance. Take care near the pleated area, as they have a tendency to want to open up. And yes, I remembered to switch to a white thread before sewing.

Also be careful not to let the fabric slip as you’re sewing. With all the fullness built in, and the bias of the neck seam, it’s very easy for things to get out of alignment here and there.

Trim the collar / neck seam allowance to 1/4″. It’s easiest to do this before pressing.

Press the collar and neck seams up towards the collar. Again, you’ll have better results by trimming the seam allowance beforehand, taking out some of the tension in the curved areas.

Here’s a very tiny mishap in the collar, caused by allowing too much fabric to be gathered into the area, or perhaps not being careful enough with my sewing machine. I ended up just leaving this, but the easiest fix would be to unpick the stitches within about 1″ of the area, baste, and sew again.

Attaching the Inner Collar

Lay the inner collar under the outer collar, right sides together.

Beginning from the center back and working your way towards the front of the collar, baste the outer collar to the inner collar.

As you’re basting, lift your left hand and allow the fabric to drape over it naturally. In effect, this makes the inner collar (below) shorter in length than the outer collar (on top), which will reduce some of the excess folds that might appear otherwise on the inside of the finished collar.

At either end, you’ll notice that the inner collar extends beyond the outer collar by about 1/8″ or so. Trim this inner collar flush with the outer collar on both ends.

At both ends of the collar, draw in the seam allowances lightly to help make your sewing more accurate.

At one end, I had a slight discrepancy in the collar lengths, in that the collar extended about 5/8″ to 3/4″ beyond the edge of the facing, rather than the 1/2″ it was supposed to be, so I had to redraw the lines to make up for this error.

Sew the collars together beginning at the end where the collar meets the placket, around the shaped front, and across to the other side. When you get to an angular section and need to change directions, rather than just making a sharp turn with your stitching, make one stitch at a diagonal across the corner. This will give a little extra room for the seam allowance when the collar is turned right side out.

Trim the collar seam allowances to 1/4″.

Miter the outside corners, keeping about 1/8″ from the stitching.

Then, further taper the miters to remove excess fabric from the tight corners.

On the inside corners, snip the corner to within 1/16″ of the stitching. The closer the better, but you don’t want the linen to start unraveling.

Cut away some of the excess seam allowances at the inner corners, tapering down to the cut you just made.

Here’s what my seam allowances looked like after trimming.

At the corners, press the seam allowances to one side, being as accurate as you can. I creased the press with my fingers followed by the iron.

Finally, turn the collar right side out, paying particular attention to each of the corners. Use a seam turning tool to get the corners as sharp as possible.

Baste around the outside of the collar, about 1/2″ from the edge, arranging the seam so that the inner collar is set back about 1/16″ – 1/8″. Press with your fingers as you go.

Here you can clearly see how the inner collar has been set back, so that it will not be visible from the outside of the shirt (assuming you’re making a standing collar, at least).

Now baste across the bottom of the collar, keeping about 1″ from the raw edge, or 1/2″ from the seam itself. Keep a neutral tension between the two halves of the collar.

Now fold the raw edge of the linen collar to the inside. You may want to trim this last seam by 1/4″, as I ended up doing. Align the folded edge with the seam underneath, just covering it.

Baste the folded edge of the collar closed.

Carefully fell the folded edge to the seam underneath. You should be able to hide the diagonal part of the stitch in between the layers, should only a small stitch on the inside of the collar.

Lastly, top stitch the collar all the way around, including the neck seam, about 1/8″ from the edge. Take care around the corners to keep your stitching sharp and accurate.

Not particularly happy with the way mine turned out, obviously need more practice! And I think I chose the wrong color of thread.

In any case, this completes the collar.


Your Progress

[columns gutter=”0″]
[col]

1
Attach the outer collar.
2
Attach the inner collar.
3
Top stitch the collar.

[/col]
[col align_text=”center, middle”]

0%

[/col]
[/columns]

Side and Shoulder Seams

With the lining installed, it’s time to sew the side and shoulder seams together. Begin by laying the front on the back, right sides together, and align the side seam at the armscye.

Taking the front only, pull back the edge of the lining at the armscye and pin in place, to keep it out of the way while sewing the side seam.

Pin the front to the back, right sides together, and aligning the side seam at the armscye.

Continue pinning towards the bottom of the shirt, keeping an even, neutral tension between the two pieces.

At the bottom of the front piece, make a small mark indicating the bottom of the stitch line, just at the point where the curve of the front ends.

Sew the side seam from the armscye to the mark with a machine stitch or back stitch by hand using a 1/2″ seam allowance.

Here’s the seam so far. We’ll be pressing it later when we finish the raw edges and hem the bottom of the shirt.

Shoulder Seam

Lay the shoulder seams right sides together.

Turn back the lining at the shoulder and pin to the front layer to keep it out of the way.

Turn the shirt over to the back side, and pull the back lining away from the shoulder as well, pinning it in place.

With right sides together and the linings out of the way, pin the shoulder seam at one end.

Note how I’m aligning the seams so that the ends of the seam lines meet at 1/2″ from the edge. I usually just do this by eye but if you’re more of a beginner you could measure until you develop your rock of eye further.

Pin the other end of the shoulder seam at the neck, aligning the seam lines as before.

Now pin the rest of the shoulder seam, first in the middle, and then between each of the three pins, subdividing any fullness that may be in the seam.

Sew the shoulder seam using a 1/2″ seam allowance.

Here’s how my shoulder seam ended up aligning after sewing. I think something must have slipped, one reason I prefer to baste my seams most of the time. For this shirt though, this is close enough.

Pressing

This is slightly confusing to look at, but press the shoulder seams toward the back of the shirt, keeping the linings out of the way.

Now fold the front lining in place over the shoulder seam. It should just rest naturally and freely.

And lay the back lining over the top of the shoulder seam, sandwiching the front lining in between.

Fold under the raw edge of the back lining at the shoulder seam, aligning it carefully with the shoulder seam underneath. You should be able to feel the seam through all the layers with your fingers.

Give the shoulder lining seam a good press to keep it in place.

Finally, baste the lining closed at the shoulder seam.


Your Progress

[columns gutter=”0″]
[col]

1
Sew the side seams.
2
Sew the shoulder seams.

[/col]
[col align_text=”center, middle”]

0%

[/col]
[/columns]

Installing the Lining

Shirts during the 19th century often had a lining in the front and back of the shirt, I’m guessing to help strengthen certain areas. The exact shape could vary from shirt to shirt, so I’ll be using a basic pattern for the front and back linings – feel free to alter the shape. In this lesson we’ll baste the linings into position while the shirt is still flat, and fell the edges later on after the sleeves have been attached.

Begin by tracing out the front onto a fresh sheet of paper, not including the pleated front area. Trace around the shoulders, armscye, and side of the pleated front, and then square across about 3 or so inches below the armscye for the bottom of the front lining pattern.

Add a 1/2″ seam allowance to the vertical line at the side of the pleated front. The other edges already have seam allowances included except for the bottom edge, where you can add one or just include the seam allowance as you draw the bottom edge, as I’ve done.

Here’s the completed front lining pattern. The back lining is identical to the yoke.

I was able to cut my front lining out of the excess fabric previously cut away from the pleated front area. I suspect this will work for any size, seeing as how the pattern is so proportional.

Here are the pieces for the shirt lining all cut. The back lining is identical to the yoke. However, before sewing it together, figure out which side of the lining you want facing towards you, and sew the back lining together with the appropriate sides facing each other. I’d originally wanted the wrong side facing towards my skin, but I sewed the seam right sides together which gave me the opposite result I was looking for – should have sewed it wrong sides together.

Place the front lining into position on the wrong side of the shirt, aligning the outer edges, and ensuring you have about 1/2″ overlap in the pleated front area. I chose to have the wrong side facing up so that if the shirt fabric wore through, the lining would still match underneath.

Baste the lining to the shirt, keeping your stitches at least 1″ away from the edge so they can be folded out of the way while sewing the various seams.

Now fold under the seam allowance at the pleated front and bottom edges. I kept the fold just past the stitch line of the pleated front.

Baste the folded edges to the shirt using a straight basting stitch. Keep the stitches 1″ away from the shirt’s edges.

Here’s the lining basted in place.

Turning to the back, place the back lining onto the yoke and baste across the upper edge, again keeping 1″ from the edge. You can see here how I should have sewn the lining wrong sides together so that the seam and pattern would have been on the inside. I chose just to work with my mistake instead.

Turn under the bottom edge of the lining so it just covers the seam underneath, and baste closed, keeping the stitching 1″ from either end.

It’s important to be able to turn and pin back the lining edges on the various seams to aid in construction later on. Basting the lining in now however saves us a lot of trouble fitting and fiddling with the position of the lining if we were to wait until later to install it.


Your Progress

[columns gutter=”0″]
[col]

1
Baste the linings into position.

[/col]
[col align_text=”center, middle”]

0%

[/col]
[/columns]

The Back

Construction of the back begins with piecing together the yoke. You should cut two of these (four pieces total), one for the back yoke and one for the lining.

Sew the halves of the yoke together at the center back seam and press open.

Lay the yoke on top of the back, right sides together. We must determine the area of the shirt to be gathered in – most of the period shirts I’ve seen were gathered at the center back for some reason.

The easiest way I’ve found to do this is to slide the yoke so one end is touching the armscye, and mark the other end on the shirt. Then slide the yoke to the other end and repeat the process. The area in between the two marks is what will be gathered in.

Run three rows of gathering stitches between the marks, as we did on the front at the bottom of the pleated area. Apologies for the extra marks on my shirt – I realized that I had done the layout incorrectly and started over again once or maybe twice.

Work from the wrong side, or at least pass the ends of the stitches to the wrong side so that they won’t be caught between the layers.

Here are the three rows of stitches complete. I did slightly smaller stitching here than on the front of the shirt as I just wanted to see the difference, but I’d recommend keeping them the same for consistency.

Tie the three threads together at each end.

Place the yoke on top of the shirt back, right sides together, and pin both together, matching the center of each.

Pin each end as well.

You can see here how I aligned the seams, the yoke slightly overlaps the back of the shirt.

Then evenly pin the rest of the shoulder to the yoke on each side until you get to the two marks and the gathering stitches.

Turn the entire back over – it’s easier to work this way – and gently begin pulling on one side of the threads, forming the small gathers or pleats.

When you are happy with the spacing and appearance, pin the gathers in place, about 1″ or so between each pin.

Baste a small running stitch through all layers, removing the pins and giving any final adjustments to the gathers as you work. This helps avoid running over pins with the sewing machine.

Sew the yoke seam using a 1/2″ seam allowance, and press the seams toward the neck.

And here’s the completed back of the shirt.


Your Progress

[columns gutter=”0″]
[col]

1
Sew the yokes.
2
Attach and gather the back to the yoke.

[/col]
[col align_text=”center, middle”]

0%

[/col]
[/columns]

Trimming the Neck Line

The last thing to do on the shirt front is to trim the neck and shoulder line to its final shape. Lay the pleated front pattern on top of your linen, carefully aligning the shoulders, sides, and bottom edges. Then trace the neck and shoulder line in chalk. Flip the pattern over and repeat for the other half.

If necessary, baste the two halves of the pleated front together again (mine had come undone) before doing this step.

Now very carefully baste the pleats closed along the inside of the neck and shoulder line, keeping within 1/2″ of the line – this way you won’t have to remove the stitches after attaching the collar.

I used three or even four small diagonal basting stitches here, arranging the pleats in place as I worked, to ensure there is no movement during the rest of the construction.

Finally, trim just to the inside of the lines, creating the curve of the neck and the final shoulder seams.

This completes the construction of the pleated front.


Your Progress

[columns gutter=”0″]
[col]

1
Baste and trim the front neckline.

[/col]
[col align_text=”center, middle”]

0%

[/col]
[/columns]

Finishing the Raw Edges

Turning to the inside of the shirt, you can see there are a few raw edges left along the sides and bottom of the placket that must be finished off to prevent fraying. Begin by clipping the corners at the bottom at a diagonal, about 1/4″ in length. Cut through the seam allowance of both the shirt and the pleated front section.

Working on the sides of the pleat, turn in the shirt’s seam allowance as shown. Give it a press with your fingernails.

Then fold the seam allowance in as well.

Overcast the edges by hand using a 1/4″ to 3/8″ stitch.

Turning to the bottom edge, turn under the raw edges of the shirt in the gathered / pleated area.

Carefully fell to the bottom of the pleated front, trying to catch only the first layer of pleats, keeping the stitches invisible from the right side. My stitch was about 1/4″ in length, though I made smaller stitches in areas where the pleats were a bit denser.


Your Progress

[columns gutter=”0″]
[col]

1
Fell or overcast the raw edges of the shirt front.

[/col]
[col align_text=”center, middle”]

0%

[/col]
[/columns]

Bottom of Pleats

This probably would have been a little easier to do before attaching the pleats to the shirt front, but baste the pleats firmly together using a side basting stitch, keeping the stitches about 1/2″ from the bottom of the pleats. Arrange the pleats into position as you go in case they’ve moved out of place at all.

I like to put at least two stitches into each pleat to hold them in place better.

Now turn to the center, and mark the center of the shirt front at the bottom of the pleat area.

Pin the center of the shirt to the center of the pleated front at the placket, ensuring that the bottom of the pleats fall exactly on the seam line you drew.

Still on the wrong side, grasp the three gathering threads you tied together previously, and gently pull on the threads, distributing the shirt front fabric into neat gathers or small pleats as desired. Work on one half of the shirt front at a time.

You can distribute the gathers along the entire front edge of the pleats, or as I did, keep them towards the center of the shirt.

When you’re happy with their appearance, pin the gathered area to the pleated front. The gathering stitches should hold everything mostly in place as you work.

Repeat for the other half of the shirt front, pinning everything securely in place.

Now, diagonal baste everything even more securely through all layers, fine tuning the look and distribution of your pleats or gathers as you work. Keep the stitching 1/2″ from the bottom edge. Remove the pins as you go.

Here’s the pleated front basted to the shirt so far.

Cut a piece of linen 1 1/8″ wide by a couple of inches longer than the width of the pleated front bottom. Then mark the seam allowances (1/4″) by pulling the threads again. I pulled the threads marking the cut lines as well on the longer edges.

Crease and press the 1/4″ seam allowances to one side.

Lay the linen strip on the bottom of the pleated front, right sides up.

I like to align the linen strip so that the lower 1/4″ overlaps the main fabric of the shirt.

Baste the linen strip to the bottom of the pleats through all layers, keeping about 1/2″ from either end of the pleated front (so we can turn under the ends).

Trim both ends of the linen strip to about 1/2″ from either end.

Turn under the raw edges on both ends and secure with a couple of basting stitches in place.

Finally, back stitch or half back stitch the linen strip to the bottom of the pleats through all layers around the four edges. I used a half back stitch here since it made the visible stitch slightly smaller. You could also machine stitch this if you prefer.

I like to begin on the upper edge of the strip, about a quarter of the way from either end, to avoid starting the stitches near the ends, which could see more stress over time.

When you get to the ends and pleats that are layered more thickly, you may need to make a prick stitch – passing the needle all the way through to the underside – in order to get through all the layers. It takes a little longer but it’s worth the effort.

Continue back stitching across the bottom edge as well. I’ve found this section to be very easy after getting through all of the layers on the other edge!

Here’s the completed bottom edge of the pleated front. Remove all basting stitches from this area as necessary (though keep the center basted together at the placket).


Your Progress

[columns gutter=”0″]
[col]

1
Gather the center front.
2
Attach linen strip to bottom of pleats.

[/col]
[col align_text=”center, middle”]

0%

[/col]
[/columns]

Attaching the Pleated Front

With all of that preparatory work out of the way, we can begin attaching the pleats to the front of the shirt. Begin by laying out the shirt front and pleats, right side up, ensuring that the placket is opening in the correct direction (left over right).

Align the bottom and outer edge of the pleats carefully with the seam lines you chalked earlier. The linen should just cover the chalk lines.

Baste, from the bottom up, one side of the pleated front in place, ensuring that everything is lined up properly as you go, maintaining a neutral tension on both the pleats and the shirt underneath.

The second side of the pleated front is more awkward to reach, so I like to pin this in place before basting.

Baste the second edge of the pleats in place.

The bottom will still be left open at this point.

Carefully fell the pleated front to the shirt front along the long outside edges using 1/8″ – 1/16″ stitches. It’s a bit awkward to hold again — I found the best approach was to grasp the fabric from the outer edge of the shirt.

Each stitch is made by inserting the needle into the lower shirt fabric at a diagonal, coming out a stitch or two away from the edge of the linen. This hides most of the stitch on the inside.

The finished seam from the outside – you can barely see the stitches.

Here’s the stitch from the wrong side, showing the diagonal threads.

And here’s the progress so far with attaching the pleated front to the shirt. Next we’ll be finishing up that bottom edge.


Your Progress

[columns gutter=”0″]
[col]

1
Baste and sew the sides of the pleated front.

[/col]
[col align_text=”center, middle”]

0%

[/col]
[/columns]

Gathering Stitches

While we’re working with the shirt front, it’s easiest to add some gathering stitches to the bottom of the pleat area now rather than later. These will later be gathered up into small pleats or gathers.

Place the shirt front on the table wrong side up. Using some basting thread or other stronger thread, baste a row of running stitches along the bottom seam line (1″ from the edge), from end to end, keeping about 1/2″ from each end so the thread will not be caught up in the seams later on.

These stitches can be anywhere from 1/8″ or even less if you’re feeling ambitious, to 1/4″ or more, depending on how fine you want your gathers after attaching the pleated front. I decided to go with a 1/4″ (roughly) for sanity’s sake.

Leave about 6″ of thread free at each end.

You can usually get at least 2 or 3 or even more stitches done in one pass of the needle, depending on the stitch length.

Here’s my first row of stitches complete. If you look closely you can see how I stopped 1/2″ from each end, as well as left about 6″ of thread at each end.

Repeat this process with a second row of stitching, about 1/8″ away from the first (towards the top of the shirt), following the same stitch pattern as the first row.

And finally, complete a third row following the same pattern of stitching. It doesn’t have to be exact but the closer the better.

If you’re skilled with this type of work you could probably leave out the third row, but if you are new to it, or just prefer to have more control and no slipping of threads and pleats, then three rows is the way to go.

Finally, tie the threads together at each end to keep the from pulling out during the next couple of steps.


Your Progress

[columns gutter=”0″]
[col]

1
Add gathering stitches to the bottom of the pleat area.

[/col]
[col align_text=”center, middle”]

0%

[/col]
[/columns]

Cutting the Front

Before moving on to attaching the pleated front to the front of the shirt, we have a little work to do on the front pattern. Trace around the entire outline of the shirt. I had previously cut the pattern to make the toile, so I taped it back together for this step.

Then, cut your pattern at the bottom and inner edge of the pleats, as shown.

Place the pattern back on your fabric and mark the new lines indicating the edge of the pleat area.

Here’s what mine looks like so far. I hope you can see the lines clearly enough!

At the bottom of the pleat area, add a 1″ seam allowance on the inner, neck side. This gives us plenty of room to work with when finishing the raw edges later on – something I’ve wished for on prior shirt projects.

Then add a 1/2″ seam allowance along the long edge.

Carefully cut out the pleated area on those inner lines.

Finally, if you’re like me and did all of your layout on the wrong side, open up the fabric and lay out the 1/2″ and 1″ seam allowances as shown. Sorry the photo skips ahead slightly!

I didn’t photograph this, but transfer the seam lines from the wrong sides to the right sides as well using the same measurements.


Your Progress

[columns gutter=”0″]
[col]

1
Cut out the front of the shirt.
2
Add seam allowances to the pleat area.

[/col]
[col align_text=”center, middle”]

0%

[/col]
[/columns]